The Juicer Problems – All You know Before Buying
Finding the best juicer in the market is an absolute must, especially for those who are fond of juicing. It talks about some The Juicer Problems of the type of juicers currently available in the market. I hope it also help you completely understand how you can choose the best juicer.
I. Problems with Masticating Juicer and How to Fix Them
One of the most common problems that happen to a masticating juicer is that it clogs. It can provide you with a delicious juicer but when the machine clogs, you will notice the entire operation stopping or slowing down. The best way to handle this is to understand what causes it so you can prevent it in the future. Here are some tips on preventing clogging in masticating juicers:
- Clean it properly – Cleaning your juicer is the key to ensuring that it continues to run smoothly. Dismantle it right away and clean thoroughly after each use. While it’s okay to soak it for a while, you have to ensure that you don’t let the produce residue harden on the parts of the juicer. Also, take note that while some chutes are challenging to clean, especially that, which is on the pulp container, it’s advisable to take each pulp from this part.
- Juice properly – The specific way you juice ingredients also contributes to clogging. Note that soft fruits and veggies and leafy veggies tend to cause the juicer to clog up. The clogging might occur in the pulp chute or auger. One way to prevent this is to mince leafy veggies if you’re using them into fine pieces. This will ensure that the veggies can easily pass through the machine. Avoid rushing the juicing process, too. Give your masticating juicer enough time to grind the produce and ingredients properly to ensure that it doesn’t clog. Also, make it a point to check the pulp outlet chute from time to time to ensure that it ejects waste pulp.
2. Can’t extract juice from soft fruits (ex. oranges, mangoes, and tomatoes)
The possible reason for this is the lack of fiber designed to push the juices from the fruits through the straining screen. You can overcome this issue by alternating soft fruits with harder ones and You also can use harder veggies to alternate the soft fruits. You can then finish the whole juicing session by putting in a hard vegetable into the machine as a means of cleaning it out.
3. Heated cap
This usually happens when you juice barley grass, wheatgrass, or any other grass. Making pasta from the juicer might also trigger the heating of the cap. In some cases, it also expands. If this happens, remember that nothing is actually wrong with your machine. The heat is actually caused by the friction produced by the gear when it pushes fine stuff into the strainer. If you notice the cap heating up then just wait for a bit until the cap cools down prior to dismantling it.
4. Heated cap
If you experience problems with the motor stalling when you are juicing then it could be because of the buildup of pulp. In case it’s accumulated beneath the cover of the machine then the best way to handle it is to slow down the speed. You should also disassemble and start cleaning the filter bowl, juicer cover, and filter basket. Find out if there are any remaining food or produce in the blades or feeding tube and clean thoroughly.
Read more: Top 10 Best Juicer in 2018
II. Problems with Centrifugal Juicer and How to Fix Them
1. Clogged top cover
If the juicer’s top cover tends to be clogged up because of the pulp, then one reason could be that you’re using an extremely high speed that it has a hard time moving the pulp from the chute and transferring it to the pulp container. What it does is it releases the pulp, instead, in the sense that it hits the top cover’s upper portion.
One way to fix this is to turn the juicing machine off. Dismantle the cover then remove the collected pulp from it. Once done, put it back to the centrifugal juicer. Start juicing again but this time, at a slower speed. You should also consider pushing down the food to the chute slowly so you can also let the blades of the juicer process it at a much slower pace.
2. Some pulp issues
It should be noted that the pulp accumulated by the juicer needs to be dry. However, remember that it won’t appear like saw dust once it comes out of your machine. It will always be a bit damp. Just make sure that when you squeeze it, it does not produce excessive amounts of liquid.
In case you accumulated overly wet pulp while also extracting juice, which is less than what you initially expected, then what you have to do is to ensure that you’re not using an extremely high speed. Use a lower speed instead. It’s because using an extremely high speed might cause the liquid to have less time moving through the filter. It might cause the liquid to cling to the pulp, triggering the excessive moisture.
Wet pulp also requires you to check the machine’s filter basket. You also have to check whether there are clogs in the mesh or if the blades are coated with food fibers. The mentioned issues might block the proper juicing of foods, causing the liquid to move away from the juicer together with the pulp. This can result in the pulp getting wetter than usual.
3. Leaks under the cover
Note that the centrifugal action might force the extracted juice against the sides of the machine’s cover between the filter basket’s mesh. In case of clogged mesh, it would be impossible for the juice to move freely and in those areas designed for proper collection. This might result in the juice spraying up in other places, causing leaks.
In this case, you have to stop the juicing right away. Unplug it from the outlet. You should then remove the basket to start cleaning. Use a nylon brush in scrubbing the mesh, too. To ensure that the mesh is already clear, check it thoroughly under the light before putting it back to the juicer.
Another way to prevent leaks is to juice at a slower speed, especially if you’re using fruits and veggies that have higher water content. In case the leaks surround the pulp container then the best way to handle it is to line this component with a plastic bag to create a tighter seal between the juicer cover and pulp container. Aside from preventing leaks, this can also result in easier cleanup.
Read more: Top 5 Best Juicer Under $100
III. Problems with Twin Gear Juicer and How to Fix Them
1. Motor doesn’t start
If your twin gear juicer’s motor tends to fail to start then there are ways to handle it. The first thing that you can do is to check whether its cord is indeed plugged to the socket. Also, ensure that the wall socket has power and that the housing is attached properly. Another possible reason for the failure of the motor to start is that some foreign objects or pieces of food are wedged in the cutter blade within the housing so make it a point to check the mentioned parts.
2. Overheating motor
In case you notice that the juicer’s motor overheat then note that it could be because you are using the wrong grid. In this case, check whether the correct grid is used and if the juicer is installed properly over the grid holder. Also, note that an extremely small grid makes it difficult to push ingredients to the grinder, causing the motor to overheat.
Another thing that you have to check out is the length of the extension cord. Use the right length of extension cord. Note that an extremely long or light one can also trigger overheating. Another way to prevent overheating is to ensure that the seeds, nuts, and grains you added to the juicer are fully dry. They should also be at room temperature. Note that moist ones might trigger overheating while producing unsatisfactory results.
3. Stops to function in the middle of juicing
Another problem that you might encounter with the twin gear juicer is it stops to function even if you are still in the middle of the juicing process. If that’s the case then note that it could be caused by the machine running for an extremely long period. With that in mind, you should let it take a break for around ten to fifteen minutes.
Another possible reason for its malfunction is that it’s overloaded. You should make it a point to unplug the machine and ensure that it takes a break for a while. However, if it still malfunctions then there’s a chance that the main reason for it is a blown fuse. If that’s the case then it would be best to seek the help of a professional. You can also contact the customer support team of your juicer’s brand.
Eventually, you will also notice that your twin gear juicer starts to leak. In some cases, the leak occurs directly at the area where the container for the pulp is hooked to the machine. In that case, you can handle the problem by putting a plastic bag within the container.
You should also allow the sides of the bag to hang once you attach the pulp collector. You can then pull the bag’s edges up and over that specific part where the juice is extracted. Another way to handle a juice leak is to ensure that you retain the cleanliness of the filter basket.
Read more: Top 5 Best Lemon Squeezer